A bag that reaches final set in 20 to 40 minutes sounds made for a quick pad, but is a slab really on the label? The answer sits in the maker’s data sheet, and the sheet gives limits as well as permission.
Yes, under the maker’s own sheet. QUIKRETE Fast-Setting Concrete Mix 1004-50 (50 lb bag) lists pouring slabs 2 in or thicker as a use, and it states no maximum size. Slabs are mixed with water, not dry-poured, and the sheet says to wait at least 4 hours before walking on the slab.
Does QUIKRETE Allow Fast-Setting Mix in a Slab?
Yes. The QUIKRETE data sheet for Fast-Setting Concrete Mix 1004-50 (50 lb bag, revised November 2025) lists pouring slabs 2 in or thicker among its uses. The same sheet lists posts, sleeves and anchors, and it gives no maximum thickness or area.
Treat 2 in as the floor for this mix, not as good practice. QUIKRETE’s general guide to sidewalks and small slabs, written for other QUIKRETE mixes, says sidewalks should be at least 4 in thick and simple small slabs normally run 4 to 6 in, depending on the load. For help picking a number, read about how thick a slab should be.
Brand and bag size matter here. Every figure below names its product, because a different bag or maker has a different sheet. To turn a slab size into bags, use the fast-setting concrete calculator.
How Is a Slab Poured With This Mix?
The 1004-50 sheet mixes slab concrete with water, about 4 pt per 50 lb bag, and it keeps dry pouring for posts only. Use a barrel-type or mortar mixer, or mix by hand, and allow at least 3/4 cu ft of mixer capacity for each bag mixed at one time.
The sheet puts maximum water below 5 pt per bag. It asks for a stiff, moldable mix with no dry pockets and no standing puddles. For the post method, see setting a fence post in concrete.
For placing, the sheet says to dampen the subgrade, fill the form to full depth and avoid partial-depth fills that could cause cold joints. Strike off and float immediately, then wait until surface water has gone before troweling or brooming.
What Do the 20-Minute and 4-Hour Limits Mean?
The 1004-50 sheet gives three time figures: final set in 20 to 40 minutes, a 20-minute placing window, and at least 4 hours before walking on the slab or setting heavy objects on it. The set time is a lab result from ASTM C191 in the sheet’s Table 1.
The placing window is a direct instruction: “Mix only as much material as can be placed in 20 minutes.” The sheet states no size limit, so this sentence is QUIKRETE’s own advice on batch size.
Final set is not a driving time. The sheet gives no wait for vehicles, so read about how soon you can drive on new concrete and ask the maker. The 60 lb QUIKRETE 1004-60 sheet is a separate document: it allows walking at 2 hours and heavy objects after 4 hours.
How Strong Is the Mix at 24 Hours and 28 Days?
Table 1 of the 1004-50 sheet lists 1000 psi at 24 hours, 2500 psi at 7 days and 4000 psi at 28 days. These are lab values for a mix with a 2 to 3 in slump, not results measured on your slab.
The sheet adds that the mix meets or exceeds the compressive strength requirements of ASTM C387. The 60 lb 1004-60 sheet lists the same 24-hour, 7-day and 28-day figures and adds 400 psi at 2 hours. Both are lab tables, so they do not tell you when a real slab can take a vehicle.
How Many 50 lb Bags Does a 10 by 10 Foot Slab Take?
A 10 ft by 10 ft slab, 4 in thick, with 10 percent waste needs 36.67 cu ft, which is 98 bags of 50 lb QUIKRETE 1004-50 at the sheet’s yield of about 0.375 cu ft per bag. The tool’s slab mode runs this same sum.
- Volume. 10 x 10 x 4/12 = 33.33 cu ft.
- Waste. 33.33 x 1.10 = 36.67 cu ft (10 percent is the calculator’s waste setting).
- Bags. 36.67 / 0.375 = 97.8, so 98 bags. That is 98 x 50 = 4,900 lb of bags.
- Cubic yards. 36.67 / 27 = 1.36 cu yd. Arithmetic: 27 / 0.375 = 72 bags per cubic yard.
One more line of arithmetic, not a maker figure: mixing all 98 bags together would need at least 98 x 0.75 = 73.5 cu ft of mixer capacity at the sheet’s 3/4 cu ft per bag.
Where Do Joints, Curing and Weather Rules Come In?
The 1004-50 sheet asks for 1 in deep control joints every 6 to 8 ft, careful curing and freeze protection. Its other limits are short and specific:
- Curing. Use QUIKRETE Acrylic Concrete Cure & Seal, or moist cure for five days in warm weather (70 F or higher) or seven days in cold weather (60 F to 70 F).
- Curing compound. Skip it when rain or temperatures below 60 F are expected within 24 hours.
- Freezing. Protect the slab from freezing for at least 48 hours.
- De-icers. Keep them off for at least 28 days.
Other guidance differs. NRMCA CIP 6 (read on a third-party hosted copy, accessed 2026-10-21) sets contraction joint depth at no less than 1/4 of the slab thickness and at least 1 in. It spaces joints 24 to 36 times the thickness, about 10 ft for a 4 in slab.
That works out to 8 to 12 ft (arithmetic: 24 x 4 in and 36 x 4 in), looser than QUIKRETE’s 6 to 8 ft. Follow your own product sheet, contract or local rule, and do not average the two.
How Do Fast-Setting Mixes Compare by Maker?
They differ by maker, product and bag size, so the table keeps each document separate. Never read one row’s numbers into another.
| Maker, product and document | Minimum slab thickness | Final set | Wait before load | Yield | Water |
|---|---|---|---|---|---|
| QUIKRETE 1004-50, 50 lb (data sheet, November 2025) | 2 in | 20 to 40 min | At least 4 h before walking or heavy objects | About 0.375 cu ft | About 4 pt; maximum below 5 pt |
| QUIKRETE 1004-60, 60 lb (data sheet, undated) | 2 in | 20 to 40 min | Walk at 2 h; heavy objects after 4 h | About 0.45 cu ft | About 5 pt; maximum below 6 pt |
| Sakrete, 50 lb (distributor listing) | At least 2 in | About 30 min | Foot traffic in under six hours | 0.38 cu ft | Not stated |
The Sakrete row comes from an Oldcastle APG distributor listing (accessed 2026-10-21), not a data sheet. A Sakrete data sheet was not read.
QUIKRETE also sells FastSet Concrete Mix 1004-51, a 70 lb product with its own data sheet. Do not apply the 50 lb figures to it. For more estimators, browse the slabs and flatwork calculators.
Enter your slab size and thickness to estimate your 50 lb bag count, then check the thickness, mixing and timing rules on the data sheet for your bag.
FAQs About Fast-Setting Concrete Slabs
Can you pour a slab with fast-setting concrete mix?
Yes, with QUIKRETE Fast-Setting Concrete Mix 1004-50, whose data sheet lists slabs 2 in or thicker as a use. The sheet states no maximum thickness or area. Follow the sheet for the product you buy.
Is fast-setting concrete dry-poured for slabs?
No. The 1004-50 sheet reserves dry pouring for posts. For slabs it says to mix with water, about 4 pt per 50 lb bag, with a maximum below 5 pt, in a mixer or by hand.
How long before I can walk on a fast-setting slab?
QUIKRETE 1004-50 says wait at least 4 hours before walking on the slab or placing heavy objects. The 60 lb 1004-60 sheet allows walking at 2 hours and heavy objects after 4 hours.
How much fast-setting concrete can I mix at one time?
QUIKRETE’s sheet says to mix only as much as can be placed in 20 minutes. It also asks for at least 3/4 cu ft of mixer capacity for each 50 lb bag mixed at once.
How far apart do control joints go in a fast-setting slab?
QUIKRETE 1004-50 says 1 in deep every 6 to 8 ft. NRMCA CIP 6 gives 24 to 36 times the slab thickness, about 10 ft for 4 in. Follow your own product, contract or local rule.
How long does a fast-setting slab need to cure?
QUIKRETE 1004-50 calls curing important. Use Cure & Seal, or moist cure five days in warm weather (70 F or higher) or seven days in cold weather (60 F to 70 F).
Is QUIKRETE FastSet the same as Fast-Setting Concrete Mix?
No. FastSet 1004-51 is a separate 70 lb QUIKRETE product with its own data sheet. Do not use its figures for the 50 lb Fast-Setting Concrete Mix.
Sources and Further Reading
References Used in This Article
- QUIKRETE, Fast-Setting Concrete Mix data sheet 1004-50 (revised November 2025), accessed 2026-10-21.
- QUIKRETE, Fast Setting Concrete Mix data sheet 1004-60 (60 lb, undated), accessed 2026-10-21.
- QUIKRETE, Concrete Sidewalks and Small Slabs (general project guide), accessed 2026-10-21.
- NRMCA, CIP 6 Joints in Concrete Slabs on Grade (third-party hosted copy), accessed 2026-10-21.
- QUIKRETE, FastSet Concrete Mix data sheet 1004-51 (70 lb, separate product), accessed 2026-10-21.
This guide reports what the maker sheets say and does not replace them. Fast-setting mixes differ by maker and bag size, so follow the data sheet printed for the product you buy. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-21.

Shakeel Muzaffar is the Founder and Editor-in-Chief, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality and formula verification to ensure accurate, practical, and easy-to-use calculators.