Gravel Driveway Calculator

Quick answer

A gravel driveway calculator estimates how many tons of stone a gravel driveway needs, one layer at a time. Each layer is area times depth, converted to cubic yards and then to tons with its density, and the total gets a waste allowance. The base, middle and top layers can each have their own depth and stone type.

Updated 2026-10-17By Shakeel Muzaffar | Reviewed by Prof. Dr. Khalil Mudassar, PhD
Try
Your details
Driveways and Paving
ft
Length of the driveway in feet.
ft
Width in feet. A single car is about 10 to 12 ft; two cars about 20 to 24 ft.
in
Depth of the base layer, the coarsest stone at the bottom. Use the depth from your plans or contractor. Enter 0 to skip.
ton/yd3
Bulk density of the base stone. Crusher run is about 1.5; confirm with your supplier.
in
Depth of the middle layer, usually a finer stone. Enter 0 to skip.
ton/yd3
Bulk density of the middle stone. Number 57 crushed stone is about 1.4.
in
Depth of the top or wearing layer. Enter 0 to skip.
ton/yd3
Bulk density of the top stone. Use the density from your supplier.
%
Extra stone for spillage, uneven ground and compaction. Applies to the total tons.
$
Delivered price per ton from your quote. Leave blank to skip the cost.
$
Flat delivery or minimum-load charge from the quote. Leave blank for none.
Your results

Tons of stone to order

—
Base layer tons—
Middle layer tons—
Top layer tons—
Estimated stone cost—
Cost per square foot—

Calculations run in your browser. Inputs are not sent to our servers; anything you Save stays in this browser only.

Saved results (0)
Calculator GuideMethod, worked examples, factors and FAQ

How to Use the Gravel Driveway Calculator

  1. Enter the driveway length and width in feet.
  2. Enter the depth and density of each layer: base, middle and top. Leave a depth at zero to skip that layer.
  3. Set the waste allowance. If you have a quote, enter the price per ton and any delivery fee.
  4. Read the result: the tons to order, the tons for each layer, and the cost if you entered a price.

Here is what each result line means:

ResultWhat it means
Tons of stone to orderTotal tons for all layers, including waste.
Base, middle and top tonsTons for each layer, including waste.
Estimated stone costTons to order times your price, plus delivery.
Cost per square footThe stone cost over the driveway area.

What Is a Gravel Driveway Calculator?

A gravel driveway calculator estimates the stone a gravel driveway needs. A gravel drive is built in layers: a coarse base at the bottom, a finer middle layer, and a top layer that wears under traffic. Each layer has its own depth and its own stone, so the tool keeps them separate and adds them up.

The result is tons, because gravel is sold by the ton. To size the material for a concrete driveway instead, use the concrete calculator; for the base under a paved drive, the gravel base calculator.

How the Gravel Driveway Calculator Works

Cubic yards per layer
yd = A x d / 324
Tons per layer (before waste)
tons = yd x rho

Each layer is worked out the same way. Area times depth in inches, divided by 324, gives cubic yards, since 324 is 12 inches per foot times 27 cubic feet per cubic yard. Multiplying by the density gives tons. The tool adds the three layers and applies the waste allowance to the total.

  1. For each layer, find the cubic yards: area times depth in inches, divided by 324.
  2. Multiply each layer by its density to get tons.
  3. Add the layers and apply the waste allowance to get the tons to order.
  4. If you entered a price, multiply the tons by it and add the delivery fee.

Gravel Driveway Example

Suppose you are building a 20 by 40 foot driveway, 800 square feet, with a 4 inch base at 1.5 tons per cubic yard, a 2 inch middle layer at 1.4, a 1 inch top layer at 1.4, and 10 percent waste. These depths and densities are an example, not a standard.

Calculation: base = 800 x 4 / 324 = 9.88 cubic yards, times 1.5 = 14.81 tons. Middle = 800 x 2 / 324 = 4.94 cubic yards, times 1.4 = 6.91 tons. Top = 800 x 1 / 324 = 2.47 cubic yards, times 1.4 = 3.46 tons. The layers total 25.19 tons. With 10 percent waste, that is 27.70 tons to order.

The lesson: the base is most of the stone, because it is the thickest layer. The top layer is the smallest share, so a thin top does not change the order much.

Factors That Change How Much Gravel a Driveway Needs

Layer Depths

The depth of each layer drives the tonnage more than anything else. Use the depths in your plans or from your contractor, and enter zero for any layer you are not using.

Stone Density

Angular crushed stone packs denser than rounded river rock, so the same volume weighs more. Use the density from your supplier; the defaults are planning values.

Waste and Compaction

Stone compacts and spills, and uneven ground needs more. The waste allowance covers both.

Delivery

A delivery or minimum-load fee can matter on a short driveway, so read the fee lines on the quote.

Gravel Driveway Cost Comparison

Gravel is usually the lowest-cost surface to build, but its cost depends on the stone, the depth and the delivery, not on a fixed rate. Compare quotes on the same tonnage. For a paved alternative, the concrete driveway cost calculator prices a concrete drive from your own quotes.

Quote lineGravelConcrete
Surface materialTons of stoneCubic yards of concrete
BaseLayers, in tonsGravel base, in cubic yards
MaintenanceRegrading and topping upSealing and crack repair

When to Use a Gravel Driveway Calculator

Ordering Stone

Get the tons for each layer before you call the supplier, so the order matches the job.

Comparing Quotes

Check each quote against the tons the tool gives, so you can see if the supplier is pricing the same volume.

Planning a Layered Build

Use the layer tons to see how much of the order is base, and how much is top.

Common Mistakes When Ordering Gravel for a Driveway

1. Leaving Out a Layer

A driveway without a base or top layer uses less stone than planned. Enter each layer, or zero.

2. Using Loose Depth for Compacted Stone

Compacted stone takes less depth than loose stone. Use the depth the plans or contractor give for the finished layer.

3. Ordering by the Cubic Yard

Gravel is sold by the ton, and the density changes the tons. Convert with the supplier density.

4. Forgetting the Waste Allowance

Spill, uneven ground and compaction use stone. Leave a margin.

Accuracy and Limitations

The arithmetic is exact. The tonnage is only as good as the depths and densities you enter.

What it calculates accurately

  • Cubic yards and tons for each layer from area, depth and density
  • The total tons to order after waste
  • The stone cost and cost per square foot from a price you enter

What it does not account for

  • Subgrade condition, drainage, grading and slope
  • Compaction loss beyond the waste you enter
  • Local stone prices, tax and hauling beyond your figures
  • The structural design of the base for your vehicles

How We Estimate Gravel Driveway Tonnage

Method
For each layer: cubic yards = area x depth in inches / 324; tons = cubic yards x density. Order = sum of layers x (1 + waste). Cost = order x price per ton + delivery.
Inputs used
Dimensions, three layer depths and densities, waste, and an optional price per ton and delivery fee.
Densities
Planning values in tons per cubic yard: crusher run 1.5, number 57 crushed stone 1.4, river rock 1.3. Confirm with your supplier.
Conversions
324 = 12 inches per foot x 27 cubic feet per cubic yard.
Rounding
Tons to two decimals. Round up when you order.
Edge cases
Zero or blank dimensions return a prompt; all depths at zero is blocked; blank densities fall back to the planning values; blank prices leave the cost blank.

Frequently Asked Questions About Gravel Driveways

How many tons of gravel do I need for a driveway?

Tons = area times depth in inches, divided by 324, times the density, for each layer. A 20 by 40 foot driveway with a 4 inch base, 2 inch middle and 1 inch top is about 27.7 tons with 10 percent waste.

How thick should a gravel driveway be?

Use the layer depths in your plans or from your contractor. This tool does not set the depths; it converts the depths you enter into tons.

Is gravel sold by the ton or the yard?

Usually by the ton, though some suppliers quote by the cubic yard. Convert with the stone density from your supplier.

What is the difference between base and top gravel?

The base is the coarser, thicker layer that carries the load. The top is the surface layer that wears under traffic. The middle layer is optional and sits between them.

Does a gravel driveway need all three layers?

Not always. Enter zero for any layer you do not use. The layers you keep should match the plan for your site.

Which stone density should I use?

Use the density from your supplier. The defaults are planning values: crusher run about 1.5 tons per cubic yard and number 57 crushed stone about 1.4.

Why is my gravel order more than the volume?

The tool adds waste for spill, uneven ground and compaction. Stone is also sold by weight, so the density drives the order.

Does this include delivery and tax?

Only a delivery fee you enter. Tax, hauling beyond your figures and site work are not included.

Is my data saved?

No. The calculation runs in your browser and nothing you enter is stored or sent anywhere.

Sources

Related Calculators

Ordering gravel for a driveway?

Explore the concrete calculators

This calculator is for general estimating only and is not a quote or professional advice. Gravel density varies with the stone type, angularity and moisture, and gravel is sold by the ton or yard at local prices. Confirm the depths and tonnage with your contractor and supplier, and check the price from a written quote. Spotted an error? Let us know.