Asphalt Patch Calculator

Quick answer

An asphalt patch calculator estimates how many tons of hot mix a patch needs. It multiplies the patch area by its compacted depth and the mix density, divides by 2,000 to get tons, then adds waste. Optional cost lines use the price you enter from a quote.

Updated 2026-10-17By Shakeel Muzaffar | Reviewed by Prof. Dr. Khalil Mudassar, PhD
Try
Your details
Driveways and Paving
ft
Length of the area to patch, in feet.
ft
Width of the area to patch, in feet.
in
Finished compacted depth in inches. Use the depth your contractor or the repair specification gives.
lb/ft3
Compacted hot-mix density. 145 is the usual planning value; mixes run about 140 to 150. Confirm with your supplier.
%
Extra for uneven edges, spillage and compaction loss. Applies to the asphalt.
$
Delivered price per ton from your quote. Leave blank to skip the cost.
$
Flat charge from the quote. Leave blank for none.
Your results

Asphalt to order (tons)

—
Patch area—
Tons before waste—
Estimated asphalt cost—
Cost per square foot—

Calculations run in your browser. Inputs are not sent to our servers; anything you Save stays in this browser only.

Saved results (0)
Calculator GuideMethod, worked examples, factors and FAQ

How to Use the Asphalt Patch Calculator

  1. Enter the length and width of the patch in feet.
  2. Enter the compacted depth in inches, from the repair specification or your contractor.
  3. Check the density (145 is the usual planning value) and set the waste allowance.
  4. If you have a quote, enter the price per ton and any delivery fee.
  5. Read the result: the tons to order, the tons before waste, and the cost if you entered a price.

Here is what each result line means:

ResultWhat it means
Asphalt to order (tons)Compacted tons including waste.
Tons before wasteThe tons the patch volume needs, before waste.
Estimated asphalt costTons to order times your price, plus delivery.
Cost per square footThe cost over the patch area.

What Is an Asphalt Patch Calculator?

An asphalt patch calculator estimates the hot mix a repair needs. A patch is a small area of paving replaced or built up, such as a pothole or a utility trench. Because the area is small, the tonnage is small too, and rounding matters.

The tool sizes the mix only. For a whole driveway, use the concrete driveway cost calculator to compare a paved option, and the gravel base calculator for the aggregate under it.

How the Asphalt Patch Calculator Works

Asphalt tons (compacted)
tons = A x (T / 12) x d / 2000

The tonnage uses the compacted density, because that is what you buy and place. Waste covers uneven edges, spillage and compaction loss. Cost is added only if you enter a price.

  1. Find the patch area: length times width.
  2. Convert the compacted depth to feet, multiply by the area and the density, and divide by 2,000.
  3. Add the waste allowance to get the tons to order.
  4. If you entered a price, multiply the tons by it and add any delivery fee.

Asphalt Patch Example

Suppose you are patching a 10 by 12 foot area, 3 inches compacted, at 145 pounds per cubic foot, with 10 percent waste. The quote is $120 per ton and a $100 delivery fee. These are example figures.

Calculation: the area is 120 square feet. Compacted tons = 120 x (3 / 12) x 145 / 2,000 = 2.175 tons (the tool shows 2.17 to two decimals). With 10 percent waste, 2.175 x 1.10 = 2.39 tons to order (2.3925). Material is 2.3925 x $120 = $287.10, plus $100 delivery gives $387.10, or $3.23 per square foot.

The lesson: on a small patch the fixed delivery fee can be most of the cost, so compare quotes on the same minimum load.

Factors That Change How Much Asphalt a Patch Needs

Depth

The compacted depth drives the tonnage more than anything else. Use the depth from the repair specification.

Density

Mixes run about 140 to 150 pounds per cubic foot. Use the density your supplier gives.

Edges and Waste

Uneven edges and compaction loss use extra mix. The waste allowance covers them.

Delivery and Minimum Loads

On a small patch, a delivery or minimum-load fee can outweigh the material. Read the fee lines on the quote.

Asphalt Patch Cost Comparison

A patch is usually quoted as a lump sum or by the ton. Compare quotes on the same tonnage, depth and delivery, so that one contractor’s minimum load does not hide a higher price per ton.

Quote lineWhat to compare
MixPrice per ton and the tons the quote assumes
DeliveryFee or minimum load
LaborPlacing and compaction, per patch or per ton

When to Use an Asphalt Patch Calculator

Ordering a Small Repair

Get the tons before you call the plant, so the minimum load and the order match.

Checking a Lump-sum Quote

Estimate the tons yourself and see whether the quote covers the depth it says.

Planning Several Patches

Add the tons for each patch to see if one delivery covers the whole job.

Common Mistakes When Ordering Asphalt for a Patch

1. Using Loose Depth

Compacted depth is less than loose depth. Use the finished compacted depth.

2. Ignoring the Minimum Load

A small patch may pay for a full minimum load. Check the quote.

3. Forgetting the Waste Allowance

Uneven edges and compaction loss use mix.

4. Comparing Quotes with Different Depths

Two quotes only compare if they assume the same depth and tonnage.

Accuracy and Limitations

The arithmetic is exact. The tonnage is only as good as the depth and density you enter.

What it calculates accurately

  • Tons of compacted mix for a patch from area, depth and density
  • The tons to order after waste, and the cost from a price you enter

What it does not account for

  • Subgrade preparation, cutting out the old pavement and base repair
  • Tax, permits and traffic control
  • Mix design, compaction method and warranty differences between contractors

How We Estimate Asphalt Patch Tonnage

Method
Tons = area x (depth in inches / 12) x density / 2,000; order = tons x (1 + waste); cost = order x price per ton + delivery.
Density
Compacted hot mix at about 145 lb/ft3 by default (mixes run about 140 to 150). Confirm with your supplier.
Prices
None are built in. Every price is entered from a quote.
Edge cases
Zero or blank dimensions and depth return a prompt; blank waste counts as zero; blank prices leave the cost blank.

Frequently Asked Questions About Asphalt Patches

How much asphalt do I need for a patch?

Tons = area times compacted depth in feet, times density, divided by 2,000, then add waste. A 10 by 12 foot patch at 3 inches needs about 2.2 tons before waste, or about 2.4 with 10 percent waste.

How deep should an asphalt patch be?

Use the compacted depth from the repair specification or your contractor. This tool sizes the mix for the depth you enter; it does not set the depth.

What density should I use for asphalt?

About 145 pounds per cubic foot is the usual planning value for compacted hot mix. Mixes run about 140 to 150, so confirm with your supplier.

Why is the waste allowance needed?

Uneven edges, spillage and compaction loss use mix beyond the volume of the hole. The waste allowance covers them.

Is asphalt sold by the ton?

Usually, yes. Convert the compacted tons with the density from your supplier, and check the minimum load.

Does this include delivery?

Only a delivery fee you enter. Minimum-load charges, tax and traffic control are not included.

Can I use this for a utility trench?

Yes, if the trench is a rectangle. Enter its length, its width and the compacted depth. A trench with irregular ends needs a longer length or an extra section.

Is a patch the same as a new driveway?

No. A patch replaces a small area of pavement, while a driveway is a full paved surface. For a whole driveway, use the asphalt driveway cost calculator in the hub, which covers the base and labor.

Is my data saved?

No. The calculation runs in your browser and nothing you enter is stored or sent anywhere.

Sources

Related Calculators

Repairing a paved surface?

Explore the concrete calculators

This calculator is for general estimating only and is not a quote or professional advice. Asphalt density varies with the mix, and patch depth and method depend on the pavement and the repair. Confirm the depth, density and tonnage with your paving contractor and supplier, and check the price from a written quote. Spotted an error? Let us know.