How many gallons of paint does one room need? Start with the wall area, not the floor. Two Sherwin-Williams interior paints list 350 to 400 square feet per gallon, and that range drives the answer.
Measure the walls, multiply the distance around the room by the wall height, and subtract doors and windows. Divide the remaining area by the coverage per gallon, multiply by the number of coats, and round up. Sherwin-Williams data sheets list 350 to 400 square feet per gallon for interior latex paint. For new drywall, both sheets call for two coats.
Measure the Walls and Subtract the Openings
Wall area is the distance around the room times its height, minus the doors and windows. This method counts walls only, not ceilings or trim.
To get the distance around the room, add the length and width, then double the sum. Multiply that by the wall height. A 12 by 15 foot room with 8 foot walls gives 2 x (12 + 15) x 8, or 432 square feet of wall.
Next, take off the openings. The calculator subtracts 21 square feet for each door and 15 for each window. Those are the calculator’s own approximations, and neither paint source gives them. You can run these steps with your own room size in the GeniesMag paint calculator.
How Much Area One Gallon Covers
Sherwin-Williams interior latex paints cover 350 to 400 square feet per gallon, according to their data sheets. The calculator’s default is 350, the low end of that range.
The SuperPaint Interior Latex Flat sheet, revised 08/2026, gives that range at 4 mils wet and 1.4 mils dry. The Emerald Interior Latex Matte sheet, also revised 08/2026, gives the same range at 4 mils wet and 1.6 mils dry. These are manufacturer figures for each product. Real coverage on porous or textured walls is not verified in these sources.
The Purdue page is much older. Purdue University Extension NCR-135 covers exterior wood, marked Rev 3/86, and it says: “One gallon of paint will cover about 400 square feet of surface area.” Treat that line as background only, because it does not describe interior walls.
How Many Coats Does a Room Need?
For new drywall, both Sherwin-Williams sheets call for two coats. The calculator defaults to two coats and also offers one.
The SuperPaint sheet gives two coats of SuperPaint used as its own primer, or one coat of primer followed by two coats. The Emerald sheet gives two coats over primer, or two coats of Emerald used as its own primer.
These sources do not verify one coat for a same-color repaint, so ask the paint maker for that job. The flow below shows the decision.
A Worked Example for a 12 by 15 Foot Room
A 12 by 15 foot room with 8 foot walls, one door and two windows needs 3 gallons at 350 square feet per gallon with two coats. Here is the full path.
- Wall area. 2 x (12 + 15) x 8 = 432 square feet.
- Openings. 1 door x 21 = 21, and 2 windows x 15 = 30, so 51 square feet.
- Net wall. 432 – 51 = 381 square feet.
- Paint needed. 381 x 2 coats / 350 = 2.177 gallons. The calculator shows 2.18.
- Whole gallons. Round 2.177 up to 3 gallons.
Changing the coverage figure can change the gallon count. The table shows the same 381 square feet at the three coverage options the calculator offers.
| Coverage option (sq ft per gallon) | Exact gallons | Gallons to buy |
|---|---|---|
| 300, for textured or porous walls (calculator option; not verified here) | 2.540 | 3 |
| 350, the calculator default (low end of the data sheet range) | 2.177 | 3 |
| 400, best case for primed smooth walls (calculator option; top of the data sheet range) | 1.905 | 2 |
Mistakes and Limits to Check Before You Buy
Most estimate errors come from the inputs, not the math. Check these points before you buy.
- A blank height becomes 8 feet. The calculator treats an empty ceiling height as 8 feet without warning, so enter the real wall height.
- No waste is added. The calculator adds no waste or overage factor. Any margin for spills, touch-ups or uneven walls is your call.
- Any fraction of a gallon rounds up to the next whole gallon, so the figure shown is never below the exact amount the calculator computes.
- The calculator has no primer input, so it counts only the finish paint.
- The 21 and 15 square foot allowances for doors and windows are the calculator’s approximations, not data sheet figures.
- Coverage on porous or textured walls is not verified here. Use the figure from your product’s data sheet for those surfaces.
The calculator gives a starting number. Compare it with the data sheet for your product before you buy.
Enter your room size, openings, coats and coverage in the paint calculator to get whole gallons.
FAQs About Paint Quantity and Coverage
How many gallons of paint do I need for a 12 by 15 room with 8 foot walls?
Three gallons, at 350 square feet per gallon with two coats. The wall area is 432 square feet, minus 51 for one door and two windows, leaving 381 square feet.
Do I subtract doors and windows from the paint area?
Yes. The calculator subtracts 21 square feet for each door and 15 for each window. Those allowances are the tool’s own approximations, not figures from the Sherwin-Williams sheets or the Purdue guide.
How many coats of paint does new drywall need?
Two. Both Sherwin-Williams data sheets call for two coats on new drywall, whether over primer or with a self-priming paint.
Does the calculator add extra paint for waste?
No. The calculator adds no waste or overage factor. It rounds the result up to whole gallons, so any margin for touch-ups or spills is up to you.
What coverage should I use for textured or porous walls?
The calculator offers 300 square feet per gallon for textured or porous walls. The sources in this article do not verify that figure, so check the data sheet for your specific paint and surface.
Is 400 square feet per gallon realistic for a room?
It is the top of the range in both Sherwin-Williams data sheets, measured at 4 mils wet. The calculator calls it a best case for primed, smooth walls, and its default is 350.
Can I use the Purdue coverage figure for interior walls?
No. The Purdue NCR-135 guide covers exterior wood and is marked Rev 3/86. Its figure of about 400 square feet per gallon is background only, not guidance for interior walls.
Sources and Further Reading
References Used in This Article
- Sherwin-Williams, SuperPaint Interior Latex Flat, product data sheet 101.02A (manufacturer data, revised 08/2026), accessed 2026-11-15.
- Sherwin-Williams, Emerald Interior Latex Matte, product data sheet 101.08MAB (manufacturer data, revised 08/2026), accessed 2026-11-15.
- Purdue University Extension, NCR-135, Selection and Application of Exterior Finishes for Wood (extension; old exterior-wood guidance, Rev 3/86), accessed 2026-11-15.
This article gives estimates from manufacturer coverage figures and one older exterior guide. It does not replace the data sheet for your product. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-15.

Shakeel Muzaffar is the Founder and Editor-in-Chief, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality and formula verification to ensure accurate, practical, and easy-to-use calculators.