How to Build a Gravel Driveway

How much does gravel shrink once it is packed down? On public gravel roads, the Federal Highway Administration (FHWA) says ordinary compaction cuts the volume by 30 percent or more in many parts of the country. That one fact shapes how to build a gravel driveway: how deep you spread stone and how many tons you order.

Quick Answer

To build a gravel driveway, fix the subgrade and drainage first, then shape a crown: 2 percent in a Wisconsin DOT detail, about 4 percent in FHWA’s gravel road guide. Lay 4 to 6 in of compacted aggregate base (San Luis Obispo County, WisDOT) and at least 3 in of surface gravel (FHWA). Local rules decide.

What Comes Before the Stone: Subgrade and Drainage

A gravel driveway is only as strong as the soil under it, so fix the subgrade and drainage before any stone arrives. Penn State’s Center for Dirt and Gravel Road Studies (public unpaved roads, Pennsylvania) says surface performance is limited by base stability.

The FHWA and South Dakota LTAP guide for public gravel roads says to clear trees, stumps, roots and large rocks and dig out saturated organic soil. Penn State adds that the surface copies the shape of the base, so shape the base first.

Sources split on packing the subgrade:

  • Compact it. San Luis Obispo County Fire (CAL FIRE) drawing FP-9, for fire-access private driveways, compacts the top 12 in of subgrade to 95 percent relative compaction.
  • Leave it loose. The City of Santa Barbara’s permeable driveway guidance leaves the subgrade uncompacted, or under 90 percent, so storm water soaks in.
  • Compact or wait. Keller and Sherar (USDA Forest Service, 2003, low-volume rural roads) say to compact the subgrade or let a new road settle for several weeks.

Where the driveway crosses a roadside ditch, the road authority may require a culvert pipe. Some cities, Santa Barbara among them, may require concrete, asphalt or pavers from the property line into the lot.

How Deep Should the Gravel Layers Be?

The sources here call for roughly 4 to 8 in of compacted stone, set by the soil, the traffic and the purpose.

  • FHWA (public gravel roads): a minimum gravel layer of 4.5, 5.5 or 6.5 in for 0 to 5 heavy trucks a day, on high, medium or low subgrade support. The surface course should be at least 3 in, so there is material to blade.
  • Penn State (public unpaved roads): 8 in loose compacted to 6 in, or 6 in loose compacted to 4 1/2 in.
  • WisDOT SDD 9A14 (driveway at the highway right of way): 6 in of dense base aggregate on the subgrade.
  • SLO County FP-9 (fire-access driveway): at least 4 or 6 in of Class II aggregate base, set by the soil’s R value, over 12 in of compacted subgrade. The drawing does not define R; ask the fire department.
  • Santa Barbara (permeable driveway): at least 6 to 8 in of compacted aggregate.

The example depths in our gravel driveway tonnage calculator (4, 2 and 1 in, 7 in total) are a sample, not a standard; use the depths your county, fire department or engineer sets.

Gravel driveway layers, labelled by source A cross-section of a crowned gravel driveway drawn to a depth scale of 1 inch to 8 pixels, with the crown exaggerated. The top layer is a surface course of at least 3 inches, from the FHWA guide for public gravel roads. Below it is a 6 inch base: WisDOT shows 6 inches of dense base aggregate for a driveway at the highway right of way, and San Luis Obispo County drawing FP-9 asks 4 or 6 inches of Class II aggregate base for a fire-access driveway. Under the base, FP-9 compacts the top 12 inches of subgrade to 95 percent. Native soil lies below. Gravel driveway layers, labelled by source Crown (height exaggerated) Surface course 3 in Base 6 in Compacted subgrade 12 in Native soil Surface: at least 3 in FHWA, public gravel roads Base: 6 in dense base aggregate WisDOT, driveway at highway ROW or 4 or 6 in Class II base (SLO FP-9) Subgrade: top 12 in at 95% SLO County FP-9, fire-access driveway Depths to scale (1 in = 8 px); crown height exaggerated. Each layer comes from a different source.
Three sources stacked into one build; your local rule decides which layers apply.

Dense-Graded or Permeable: Choosing the Stone

Choose dense-graded crushed stone for a tight, compacted surface, or washed open-graded stone for a permeable driveway that soaks up rain.

Penn State’s Driving Surface Aggregate (DSA) is crushed stone graded for packing density. Its fines must be crushed rock, not added clay or silt, with a Plasticity Index (PI, a measure of how clay-like fines act) of 6 or less. FHWA wants surface gravel with some plasticity as a binder, with a PI between 3 and 15 depending on yearly rainfall.

Dense-graded vs permeable gravel driveway, by source
Attribute Dense-graded, compacted Permeable (Santa Barbara)
Stone Crushed, 1.5 in top size (Penn State DSA); 1 1/4 in dense base aggregate (WisDOT) Washed, open-graded, angular crushed stone, at least 3/4 in
Fines 11 to 15 percent passing the No. 200 sieve, crushed rock, PI 6 or less (Penn State) None; no binders or top layers
Subgrade Top 12 in at 95 percent (SLO FP-9) Uncompacted, or under 90 percent
Fabric Allowed, not required (Penn State) No filter fabric under the gravel

How Much Crown Does a Gravel Driveway Need?

Plan a straight crown or cross slope between 2 percent (WisDOT) and about 4 percent (FHWA, SLO FP-9).

  • FHWA: about 1/2 in of crown per foot (about 4 percent), never over 6 percent. Build it as a straight line from shoulder to centerline; a rounded, parabolic crown leaves the middle too flat to drain.
  • Penn State: 1/2 to 3/4 in per foot, which is about 4.2 to 6.25 percent (our arithmetic). Its top end slightly exceeds FHWA’s 6 percent cap.
  • SLO FP-9: 4 percent each way from the centerline, or 4 percent one way.
  • Keller and Sherar: 3 to 5 percent, as a crown, an outslope or an inslope with a ditch.

Keller and Sherar warn, “It is difficult to create and maintain a crown on a narrow road.” They find one-way slopes generally more effective on rural roads. FHWA counters that narrow roads still need crown.

On a 12 ft driveway, each side is 6 ft wide. The center rises 1.4 in at 2 percent, 2.9 in at 4 percent, 3.0 in at 1/2 in per foot and 4.5 in at 3/4 in per foot (our arithmetic). FHWA asks for a finish within plus or minus 0.5 percent of the design slope.

Crown and cross slope by source A horizontal chart on a scale of 0 to 7 percent. WisDOT SDD 9A14, for a driveway at the highway right of way, shows 2 percent. San Luis Obispo County FP-9, for a fire-access driveway, shows 4 percent. FHWA, for public gravel roads, recommends about 4 percent and never over 6 percent. Keller and Sherar, for low-volume rural roads, give a range of 3 to 5 percent. Penn State, for public unpaved roads, gives 1/2 to 3/4 inch per foot, about 4.2 to 6.25 percent. Crown or cross slope, percent, by source WisDOT SDD 9A14 driveway at highway ROW 2% SLO County FP-9 fire-access driveway 4% FHWA and SD LTAP public gravel roads about 4% 6% max Keller and Sherar low-volume rural roads 3 to 5% Penn State DSA public unpaved roads 4.2 to 6.25% 0 1 2 3 4 5 6 7 Teal bars: one figure. Navy bars: a range. Penn State range converted from 1/2 to 3/4 in per ft.
WisDOT’s driveway detail is the flattest at 2 percent; most sources sit near 4.

Should You Put Fabric Under a Gravel Driveway?

No source read here requires fabric under every gravel driveway; it earns its place over soft, wet or weak soil. Penn State allows fabric on its program projects but does not require it. Santa Barbara rules out filter fabric under permeable gravel.

FHWA uses a woven or non-woven geotextile on soft subgrade as a separator, so fine wet soil does not pump up into the new stone. Keller and Sherar say a 200 g/m2 (6.0 oz/yd2) needle-punched nonwoven is commonly used for filtration and separation when no other information exists.

FHWA’s placement rules:

  • Smooth the soil and clear rocks and stumps.
  • Lay the fabric with no wrinkles or folds, and keep equipment off it.
  • Overlap seams at least 18 in, or sew them.
  • Place a first stone layer of at least 6 in on the fabric.

How to Build a Gravel Driveway One Compacted Lift at a Time

Spread stone in lifts at the right moisture and roll each lift before the next.

  1. Set the lift depth. FHWA places layers generally no more than 4 in loose, or up to 8 in with larger compaction equipment. Penn State places DSA in one 6 to 8 in loose lift.
  2. Wet it to optimum. FHWA works to optimum moisture for maximum density. Penn State wants DSA delivered at optimum moisture or up to 2 percent below.
  3. Pick the roller. FHWA matches sheepsfoot or pad rollers to clay and rubber-tired rollers to sandy or granular soil. Penn State uses at least a 10-ton vibratory roller.
  4. Roll toward the crown. Penn State rolls from the low edge toward the crown, never lengthwise along its top. The first pass is static, then vibratory, and the last is static.
  5. Check density. Penn State targets 95 to 100 percent of maximum dry density.

Penn State also cuts a 3 to 4 in key along the edge to support the stone.

How Many Tons of Gravel to Order

Order for the loose depth, not the finished depth, because stone shrinks as it packs.

Take the calculator’s example: 20 x 40 ft (800 sq ft) at 4, 2 and 1 in. At its planning densities of 1.5, 1.4 and 1.4 tons per cubic yard (tool settings, not source figures), the layers weigh 14.81 + 6.91 + 3.46 = 25.19 tons. The tool’s 10 percent waste allowance brings that to 27.70 tons.

Penn State’s ordering rule is width x length x 0.04 for 8 in loose packed to 6 in. On 800 sq ft, that is 32 tons of DSA. Enter 6 in at 1.5 with 10 percent waste and the tool gives 24.44 tons, about 24 percent short (our arithmetic). Enter the 8 in loose depth and it gives 32.59 tons.

Penn State’s factors imply about 1.62 tons per cubic yard loose and 2.16 compacted for DSA only (our arithmetic). FHWA’s 30 percent shrink means about 1.43 times the finished volume in loose stone.

Local rules decide. Your county road department, state DOT district office or building department sets permits and widths; your supplier knows its stone’s weight.
Turn your depths into tons

Enter loose depths and your supplier’s density in the Gravel Driveway Calculator for tons per layer.

FAQs About Building a Gravel Driveway

How thick should a gravel driveway be?

Most sources here call for about 4 to 8 in of compacted stone. FHWA sets minimums of 4.5 to 6.5 in for up to 5 heavy trucks a day on public gravel roads, and Santa Barbara asks at least 6 to 8 in.

Do I need to compact the soil before laying gravel?

It depends on the design. San Luis Obispo County’s fire-access standard compacts the top 12 in to 95 percent. Santa Barbara’s permeable design leaves the subgrade uncompacted, or under 90 percent, so rain soaks in.

Is landscape fabric required under a gravel driveway?

No source read here requires it on every driveway. Penn State allows fabric but does not require it, Santa Barbara rules it out under permeable gravel, and FHWA uses it as a separator over soft, wet soil.

Why does water stand in the middle of my gravel driveway?

The center is too flat to drain. FHWA recommends a straight-line crown of about 1/2 in per foot, or 4 percent, and warns that a rounded crown leaves the middle too flat.

Can a narrow driveway slope one way instead of having a crown?

Yes, in some standards. San Luis Obispo County allows a 4 percent one-way slope, and Keller and Sherar favor one-way slopes on narrow rural roads. FHWA says narrow roads still need crown.

How many tons of gravel does a 20 by 40 foot driveway need?

Penn State’s rule gives 32 tons of its surface aggregate for 8 in loose packed to 6 in. The calculator’s 7 in example gives 27.70 tons, including its 10 percent waste setting.

Should the top layer of a gravel driveway have fines?

For a dense surface, yes: Penn State wants 11 to 15 percent crushed-rock fines. For a permeable driveway, no: Santa Barbara requires washed stone with no binders or top layers.

Sources and Further Reading

References Used in This Article

This guide compares published road, driveway and fire-access standards. It is not an engineering design; local rules set final depths. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-15.