Stormwater Runoff From a Roof

How much water leaves your roof in a storm? Each inch of rain drops about 0.62 gallons on every square foot, according to the US EPA and Texas A&M AgriLife Extension. On a 1,000 square foot roof, that is more than 600 gallons from a single inch.

Quick Answer

Stormwater runoff from a roof starts with about 0.62 gallons of rain per square foot per inch (EPA, Texas A&M AgriLife; Seattle uses 0.623). A 1,000 square foot roof gets about 623 gallons per inch. With TxDOT’s roof coefficients of 0.75 to 0.95, roughly 467 to 592 gallons runs off (our arithmetic).

How Many Gallons of Rain Land on a Roof?

One inch of rain on one square foot of roof is about 0.62 gallons. Four public sources land on that number, give or take rounding:

  • US EPA (national). WaterSense at Work (2012) uses 0.62 gallons per square foot of collection area per inch of rain.
  • Texas A&M AgriLife Extension (Texas). An AgriLife Today article from July 2023 also uses 0.62 gallons per square foot.
  • Seattle Public Utilities (Seattle, Washington). The city’s rainwater harvesting page uses about 0.623 gallons.
  • USGS (national). Circular 1268 lists 1 inch of rain as 27,200 gallons per acre, or about 0.624 gallons per square foot.

The gaps are rounding. USGS says a cubic foot holds about 7.48 gallons, and an inch is one twelfth of a foot. The calculator uses a more precise 7.48052, and 7.48052 divided by 12 gives 0.6234 gallons per square foot per inch. Multiplying that by 43,560 square feet gives about 27,154 gallons per acre-inch (our arithmetic).

Seattle shows the rule at work: 0.25 inch of rain x 0.623 x 1,400 square feet = 218 gallons. To run your own roof size and storm, the stormwater runoff calculator does the multiplication for you.

What Runoff Coefficient Fits a Roof?

A runoff coefficient, written C, is a number from 0 to 1 that scales rainfall down to runoff in the rational method. For roofs, TxDOT gives 0.75 to 0.95 and Iowa SUDAS gives 0.95, so the answer depends on which manual your area follows.

TxDOT’s Hydraulic Design Manual (Texas), Table 4-10, puts roofs and drives and walks at 0.75 to 0.95. The Iowa SUDAS Design Manual (2024 edition), Table 2B-4.01, gives roofs, parking lots and driveways 0.95 for 5- and 10-year storms. For the 100-year storm, it uses 0.98.

Lawns spread out far more. TxDOT splits them by soil and slope, from 0.05 to 0.10 on flat sandy lawns up to 0.25 to 0.35 on steep heavy-soil lawns. SUDAS splits them by hydrologic soil group (A to D), condition and storm. SUDAS says its coefficients come from the SCS curve-number method.

The calculator uses its own settings, not either table: 0.90 for roofs and pavement, 0.25 for lawn and 0.50 for gravel. Those are tool settings, not source figures.

Runoff coefficients by surface and source TxDOT roofs 0.75 to 0.95. Iowa SUDAS roofs 0.95 for 5- and 10-year storms and 0.98 for the 100-year storm. TxDOT lawns on sandy soil 0.05 to 0.20 and on heavy soil 0.13 to 0.35, depending on slope. SUDAS lawns in good condition for a 5-year storm: soil group A 0.05, B 0.15, C 0.35, D 0.50. SUDAS gravel roads for a 5-year storm, soil groups B to D: 0.60 to 0.75. Runoff coefficient (C) by surface and source TxDOT (Texas) Iowa SUDAS TxDOT roofs 0.75 to 0.95 SUDAS roofs 0.95 (5, 10-yr); 0.98 (100-yr) TxDOT lawns, sandy soil 0.05 to 0.20 (by slope) TxDOT lawns, heavy soil 0.13 to 0.35 (by slope) SUDAS lawns, good, 5-yr A 0.05, B 0.15, C 0.35, D 0.50 SUDAS gravel roads, 5-yr 0.60 to 0.75 (B to D) 0 0.25 0.50 0.75 1.0 Sources: TxDOT Hydraulic Design Manual Table 4-10; Iowa SUDAS Table 2B-4.01 (2024).
Roofs cluster near the top of the scale in both manuals; lawns vary with soil, slope and condition.

How Much Stormwater Runoff From a Roof? A Worked Example

A 1,000 square foot roof in a 1 inch rain receives about 623 gallons and sheds roughly 467 to 592 gallons of runoff, depending on the coefficient. Here is the math (our arithmetic on the sources’ figures).

  1. Find the rain volume. 1 inch x 1,000 square feet x 0.623 gallons = about 623 gallons, using Seattle’s rule.
  2. Pick a coefficient. The tool’s roof setting is 0.90. That sits inside TxDOT’s 0.75 to 0.95 range and below SUDAS’s 0.95.
  3. Multiply. 623 x 0.90 = about 561 gallons. TxDOT’s range gives about 467 to 592 gallons, and SUDAS’s 0.95 gives about 592 gallons.

One caution about step 3. Seattle, EPA and AgriLife describe all the rain that lands on a surface. Multiplying their gallons rule by C is our inference, not a step any of them publishes.

EPA’s WaterSense at Work adds a separate idea: installers typically assume 80 percent capture efficiency for rainwater harvesting. That is a collection assumption, not a runoff coefficient. On the same roof, 623 x 0.80 is about 498 gallons caught (our arithmetic).

From rain depth to gallons to runoff Step 1: 1 inch of rain on a 1,000 square foot roof. Step 2: multiply by 0.623 gallons per square foot per inch (Seattle Public Utilities) to get about 623 gallons of rain. Step 3: multiply by a runoff coefficient; at the tool setting of 0.90 that is about 561 gallons. The step 3 multiplication is our inference. TxDOT’s roof range of 0.75 to 0.95 gives about 467 to 592 gallons. From rain depth to gallons to runoff 1. Rain on the roof 1 in of rain x 1,000 sq ft of roof Inputs you choose 2. Gallons of rain x 0.623 gal per sq ft-in = about 623 gal Seattle Public Utilities rule 3. Estimated runoff x C of 0.90 (tool) = about 561 gal This step: our inference With TxDOT’s roof range (C 0.75 to 0.95): about 467 to 592 gal of runoff. Rainwater sources describe all rain that lands; applying C is not their step.
The gallons rule is sourced; multiplying it by C is an inference, labelled as such.

Peak Flow or Volume: What Does the Rational Method Measure?

The rational method measures peak flow, the highest rate of runoff during a storm, in cubic feet per second (cfs). TxDOT presents it as a peak-flow method, not a way to total up gallons.

TxDOT writes it as Q = CIA / Z, where Z is 1 in English units. Q is flow in cfs, I is rainfall intensity in inches per hour, and A is area in acres. Iowa SUDAS uses the same form, Q = C x i x A (Equation 2B-4.01).

For a 1,000 square foot roof (about 0.023 acres) at 2 inches per hour and C of 0.90: 0.90 x 2 x 0.023 = about 0.041 cfs. That is roughly 18.5 gallons per minute at the peak (our arithmetic). The 2 inches per hour is the tool’s example, not a design storm. Your local stormwater office can say which storm and rainfall intensity to use.

The calculator also reports a volume, using C x depth x area. That line is the tool’s own simplification. We found no source for it in the manuals we read, so treat it as a rough estimate.

How the two engineering manuals frame the rational method
Point TxDOT (Texas) Iowa SUDAS (Iowa)
Equation Q = CIA / Z, Z = 1 in English units Q = C x i x A (Equation 2B-4.01)
Area limit About 200 acres, no significant storage 40 acres or less
Lawn C depends on Soil (sandy or heavy) and slope Soil group A to D, condition and storm
Rarer storms No adjustment in Table 4-10 C rises (roofs 0.95 to 0.98)
Gravel row None Gravel roads listed
Other notes Minimum 10-minute duration; uniform rainfall assumed Coefficients derived from the SCS curve-number method

What Happens to Runoff When a Lawn Becomes a Roof?

Covering an acre of lawn with roof or pavement more than triples the peak flow in the calculator’s default example. The before number, though, is the least certain part of that math.

The tool’s first example uses 1 acre (43,560 square feet), 2 inches per hour and a 2 inch storm. Lawn at its 0.25 setting gives 0.25 x 2 x 1 = 0.50 cfs. Roof or pavement at 0.90 gives 1.80 cfs, an increase of 1.30 cfs.

Its volume line gives 1,815 cubic feet (13,577 gallons) for lawn and 6,534 cubic feet (48,878 gallons) for roof. That is an increase of 35,301 gallons, from the tool’s simplified volume method.

The tool’s lawn value of 0.25 matches only TxDOT’s steepest heavy-soil band. On flat sandy lawn, TxDOT’s range is 0.05 to 0.10. In Iowa, a good lawn on group B soil is 0.15 for a 5-year storm. A poor lawn runs from 0.25 on group A up to 0.70 on group D. Your soil can move the before number more than the roof moves the after number.

Where the Sources Disagree, and Who Decides

The sources agree on the gallons rule but differ on coefficients and limits, so your local code decides which numbers apply to your site.

  • Roofs. TxDOT gives 0.75 to 0.95; SUDAS gives 0.95, or 0.98 for the 100-year storm. The tool’s 0.90 sits inside TxDOT’s range and below SUDAS.
  • Gravel. SUDAS lists gravel roads at 0.60 to 0.75 (5-year storm, soil groups B to D). TxDOT has no gravel row, and the tool uses a lower 0.50.
  • Storm size. SUDAS raises C for rarer storms. TxDOT’s Table 4-10 has no such adjustment.
  • Area limit. TxDOT allows about 200 acres; SUDAS allows 40 acres or less.
  • Gallons rule. EPA and AgriLife use 0.62, Seattle uses 0.623, and USGS works out to about 0.624. These are rounding differences.

The tables we read give no coefficients for woods, bare soil or mixed residential lots. The tool’s settings for those surfaces have no source behind them here. Before you plan drainage work, check with your local building or stormwater office. Local codes and permits set the storm, the coefficient and the method.

Run the numbers for your own roof

Enter your area, surfaces and storm in the runoff calculator for roofs and paved areas. It shows peak flow and its own volume estimate side by side.

FAQs About Stormwater Runoff

How many gallons does one inch of rain put on a square foot of roof?

About 0.62 gallons. EPA and Texas A&M AgriLife use 0.62, Seattle Public Utilities uses 0.623, and the USGS figure of 27,200 gallons per acre works out to about 0.624. The gaps are rounding.

Does all the rain on a roof become runoff?

Not in design math. Engineers apply a runoff coefficient below 1. TxDOT gives roofs 0.75 to 0.95, and Iowa SUDAS uses 0.95, so most but not all of the rain counts as runoff.

Does the runoff coefficient change with storm size?

In Iowa SUDAS, yes. Roofs rise from 0.95 for 5- and 10-year storms to 0.98 for the 100-year storm. TxDOT’s Table 4-10 has no adjustment for storm size.

Can the rational method be used for a whole subdivision?

It depends on size and local rules. TxDOT applies it to drainage areas up to about 200 acres with no significant storage, while Iowa SUDAS limits it to 40 acres or less. Your local stormwater office decides.

What is the difference between cfs and gallons in a runoff result?

Cfs is a rate: cubic feet per second at the storm’s peak. Gallons are a volume, the total water over the storm. One cubic foot holds about 7.48 gallons, according to USGS.

Is EPA’s 80 percent capture figure the same as a runoff coefficient?

No. EPA’s WaterSense at Work says installers typically assume 80 percent capture efficiency for rainwater harvesting. That describes what a collection system catches, not the C value used in the rational method.

Does a gravel driveway shed less water than a roof?

In Iowa SUDAS tables, yes. Gravel roads run 0.60 to 0.75 for a 5-year storm on soil groups B to D, against 0.95 for roofs. TxDOT lists no gravel row, and the tool uses 0.50.

Sources and Further Reading

References Used in This Article

This guide explains published runoff methods and is not a drainage design. Local codes and permits decide what your site needs. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-15.