Gallons Per Minute Calculator

Quick answer

A gallons per minute calculator gives flow in three ways. Divide gallons collected by seconds and multiply by 60, as in a bucket or pump-recovery test. Or multiply pipe area by water speed and convert with 448.8. Run in reverse, it gives the pipe size a target flow needs.

Updated 2026-10-17By Shakeel Muzaffar | Reviewed by Prof. Dr. Khalil Mudassar, PhD
Try
Your details
Plumbing, Water and Pools
Pick the question: the flow from a bucket or pump test, the flow a pipe carries, or the pipe a target flow needs.
gal
Water collected during the timed test, in US gallons. A 5-gallon bucket is common.
sec
Seconds the test took. For a pump-recovery test, use the seconds from cut-in to cut-out.
in
Inside diameter in inches, not the nominal size on the label. Check the pipe spec for the true inside diameter.
ft/s
Average speed in feet per second. LibreTexts gives a typical range of about 2 to 7 ft/s for water systems.
gpm
The flow the pipe must carry, in gallons per minute.
Your results

Gallons per minute

—
Liters per minute or area—
Flow in cubic feet per second or speed—
Pipe area or required diameter—
Required diameter (inches)—

Calculations run in your browser. Inputs are not sent to our servers; anything you Save stays in this browser only.

Saved results (0)
Calculator GuideMethod, worked examples, factors and FAQ

How to Use the Gallons per Minute Calculator

  1. Pick the question: gallons per minute from a timed fill, flow from a pipe size and water speed, or pipe size for a target flow.
  2. For a timed fill, enter the gallons collected and the seconds the test took.
  3. For a pipe, enter the inside diameter in inches and the water speed in feet per second.
  4. For a target flow, enter the gallons per minute the pipe must carry and the speed you want.
  5. Read the result and the working line below it.
ResultWhat it means
Gallons per minuteThe flow rate, from a timed fill or a pipe area and speed.
Liters per minuteThe same flow in liters, using 1 gallon = 3.785 liters.
Required diameterThe inside pipe diameter needed for the target flow at the speed you chose.

What Is a Gallons per Minute Calculator?

Gallons per minute, or GPM, is how much water passes a point each minute. It is the usual unit for a faucet, a well, a pump and a pipe. A well test, a bucket test and a pipe calculation all give a value in GPM, but they measure different things, so the method matters.

The calculator covers three questions. It turns a timed collection into a flow rate. It turns a pipe size and water speed into the flow that pipe carries. And it works backward from a target flow to the pipe size needed at a chosen speed.

Water testing is often done at a spigot near the pressure tank. For a concrete project that uses water on site, the concrete calculator sizes the concrete itself.

How the Gallons per Minute Calculator Works

Gallons per minute from a timed fill
GPM = gal / sec x 60

A timed fill gives gallons per second. Multiply by 60 to get gallons per minute. A pipe flow uses Q = A x V, the area times the speed. Because the area is in square feet and the speed in feet per second, the answer is in cubic feet per second.

Flow from a pipe
GPM = 448.8 x 0.7854 x D squared x V

LibreTexts gives the conversion: 1 cubic foot per second equals 448.8 gallons per minute. So a cubic-foot-per-second flow is multiplied by 448.8.

  1. For a timed fill, divide the gallons by the seconds and multiply by 60.
  2. For a pipe, convert the inside diameter to feet, then find the area as 0.7854 times the diameter squared.
  3. Multiply the area by the speed to get cubic feet per second, then by 448.8 to get gallons per minute.

Gallons per Minute Example

Take a bucket that holds 5 gallons and fills in 36 seconds.

Rate: 5 / 36 x 60 = 8.33 gpm. In liters, 8.33 x 3.785 = 31.5 L/min.

Now take a 4 inch inside diameter pipe at a speed of 5 ft/s. The area is 0.7854 x (4 / 12) squared = 0.0873 sq ft. The flow is 0.0873 x 5 = 0.436 cfs, and 0.436 x 448.8 = 195.8 gpm.

The reverse check uses LibreTexts: 1,500 gpm at 6.5 ft/s needs 1,500 / 448.8 = 3.34 cfs, an area of 3.34 / 6.5 = 0.51 sq ft, and a diameter of about 0.81 ft, or 9.7 inches.

Factors That Change the Flow Reading

Test Method

A timed bucket fill and a pump-recovery test measure the same unit, but Pure Water Products calls a simple timed bucket fill inaccurate for well flow. The recovery method counts the gallons drawn down between pump cut-in and cut-out.

Pump and Well Behavior

If the water level drops during the test, a reading taken over a short period can look better than the well can sustain.

Inside Diameter

A pipe labeled 1 inch may have a smaller inside diameter. Use the inside diameter, since area depends on it.

Speed

The speed in a pipe depends on the flow and the size. LibreTexts gives a typical range of about 2 to 7 ft/s for water systems.

Timed Fill and Pipe Flow Compared

Both answers come out in gallons per minute, but they answer different questions. A timed fill measures what a source delivers. A pipe calculation says what a pipe can carry at a chosen speed.

ApproachInputsAnswers
Timed fill or pump recoveryGallons and secondsMeasured flow from one source
Pipe flowInside diameter and speedFlow the pipe carries at that speed
Pipe size for a targetTarget gpm and speedInside diameter needed

When to Use a Gallons per Minute Calculator

Checking a Faucet or Hose

A quick bucket reading gives a rough GPM for a fixture or a hose bib.

Sizing a Backwash or Filter

Pure Water Products notes that many filter media need about twice the service flow for backwash, so a measured flow matters.

Choosing a Pipe for a Target Flow

Work out the inside diameter a flow needs at a chosen speed, then check it against your code.

Common Mistakes with GPM Calculations

1. Using the Nominal Pipe Size

The area depends on the true inside diameter, which is smaller than a nominal size.

2. Mixing Seconds and Minutes

A timed fill in seconds must be multiplied by 60. Entering minutes as seconds gives a result that is 60 times too high.

3. Reading One Test as the Well Yield

A single short test may not show what the well can supply over hours.

4. Skipping the Code

Velocity limits, fixture units and pressure rules come from your local plumbing code.

Accuracy and Limitations

The arithmetic is exact to the precision shown. The result depends on the gallons, seconds, diameter and speed you enter, and on the test method behind them.

What it calculates accurately

  • GPM and liters per minute from a timed collection
  • Flow from an inside diameter and an average speed
  • Inside diameter needed for a target flow at a chosen speed

What it does not account for

  • Friction loss, fittings and pressure drop
  • Well drawdown and sustained yield
  • Plumbing code limits, fixture units and permits
  • Pump curves and pressure tank settings

How We Calculate Gallons per Minute

Timed fill
GPM = gallons / seconds x 60; L/min = GPM x 3.785.
Pipe flow
Area = 0.7854 x (D/12)^2 sq ft; cfs = area x speed; GPM = cfs x 448.8.
Pipe size
cfs = GPM / 448.8; area = cfs / speed; D = sqrt(area / 0.7854) ft, then x 12 for inches.
Sources
Workforce LibreTexts (flow equation and 448.8); Lakos bucket test; Pure Water Products well flow article (see Sources).
Rounding
GPM and liters to two decimals; area to three decimals; diameter to two decimals in inches.
Edge cases
Zero seconds, a zero diameter, a zero speed and a zero target are rejected; negative gallons, speed and time are rejected.

Frequently Asked Questions About Gallons Per Minute

How do I calculate gallons per minute?

Divide the gallons collected by the seconds the test took, then multiply by 60. Five gallons in 36 seconds is 8.33 gpm.

How do I convert gpm to liters per minute?

Multiply by 3.785. Eight point three three gpm is about 31.5 liters per minute.

What is a pump-recovery test?

Measure the gallons drawn from the pressure tank until the pump turns on, then time how long the pump takes to refill that amount. Gallons over seconds, times 60, gives gpm.

How is pipe flow calculated?

Multiply the pipe area by the water speed to get cubic feet per second, then multiply by 448.8. A 4 inch inside pipe at 5 ft/s carries about 196 gpm.

What is a typical water speed in a pipe?

LibreTexts gives a typical range of about 2 to 7 feet per second for water systems. Check your code for the limit that applies to you.

Why do I use the inside diameter?

The flow area is inside the pipe. A nominal size on the label is not the same as the inside diameter, so use the inside measurement.

Is a bucket test accurate for well flow?

Pure Water Products says timed bucket fills are inaccurate for well flow and recommends the pump-recovery method. Use the recovery method when you can.

Is my data saved?

No. The calculation runs in your browser and nothing you enter is stored or sent anywhere.

Sources

Related Calculators

Checking water flow for a pool, hot tub or patio project?

Explore the concrete calculators

This calculator is for general planning and learning only. It is not a plumbing design, a code compliance check, a well yield test or professional advice. Pipe sizes, pressures, velocity limits and well capacity come from your local plumbing code, the pump and well data, and a licensed plumber or well contractor. Do not size a water supply, a drain or a backwash system from this result alone. Spotted an error? Let us know.