Rebar Chairs vs Concrete Dobies vs Bricks

Which support holds steel off the form, and which one should never go under it? Rebar chairs and concrete dobies both hold bars in place. A consultant blog says clay brick is prohibited.

Quick Answer

Rebar chairs are plastic or metal supports, and concrete dobies are precast concrete blocks. A consultant blog lists both as typical bar supports. The same blog says ACI 318, ACI 301 and CRSI prohibit clay brick, but those code texts were not read.

How a Rebar Chair Holds Steel Off the Form

A rebar chair is a plastic or metal support that holds reinforcing bar above the form. A consultant blog says bar supports keep the required concrete cover and stop the bars from shifting. The calculator guide adds that chair height sets the cover, though the calculator does not choose a height.

To count supports for a slab before you order, use the rebar chair calculator. It works from slab length, slab width, spacing and the number of mats.

Concrete Dobies: Precast Blocks Under the Bar

Concrete dobies are precast concrete blocks that sit under reinforcing bar. The same consultant blog lists concrete blocks and concrete bricks as typical bar supports. It gives no dobie size, strength or mix, so those details are not verified here.

For general concrete block sizes, read the concrete block sizes guide. Product data for a specific dobie is the better check. The manufacturer data we tried to read was not text, so this article leaves product figures out.

Why Clay Brick and Rock Fail as Supports

Clay brick is one support to avoid. A consultant blog on rebar inspections reports that ACI 318, ACI 301 and CRSI prohibit wood, clay brick and rock as supports for reinforcing steel. Those code and CRSI texts were not read for this article, so the claim is secondary.

The same blog lists concrete bricks as typical supports. Do not treat clay brick and concrete brick as the same product. The excerpt gives no reason for the clay brick rule, and this article does not supply one.

Bar supports as one consultant blog describes them (secondary sources only)
Support Material What the consultant blog says Source strength
Rebar chair Plastic or metal Typical bar support Consultant blog only
Concrete dobie or block Precast concrete Typical bar support Consultant blog only; no dobie data read
Clay brick Clay Prohibited, per the blog’s account of ACI and CRSI Consultant blog only; code not read
Wood or rock Wood or rock Prohibited, per the same account Consultant blog only; code not read

Counting Chairs on a 20 by 30 Foot Slab

The calculator guide says 3 to 4 feet is common for spacing. That is a general note, not a code limit. Take a 20 by 30 foot slab at 4 foot spacing, with one mat, as the worked example.

Along the 20 foot side, 20 / 4 = 5 spaces, plus 1, gives 6 rows. Along the 30 foot side, 30 / 4 = 7.5, and only whole spaces count, so 7 spaces plus 1 gives 8 columns. The grid is 6 x 8, or 48 chairs.

That is one chair for every 12.5 square feet, since 20 x 30 = 600 and 600 / 48 = 12.5.

Example chair grid at 4 foot spacing A plan of a 30 foot by 20 foot slab drawn to scale. Chair dots sit on a grid every 4 feet, with 8 columns along the 30 foot side and 6 rows along the 20 foot side, for 48 chairs in one mat. The side panel shows 30 / 4 = 7.5 with 7 whole spaces, giving 8 columns, and 20 / 4 = 5 spaces, giving 6 rows, so 6 x 8 = 48 chairs. Example chair grid on a 20 by 30 foot slab 20 ft 30 ft side Count check at 4 ft spacing 30 / 4 = 7.5, use 7 spaces 7 + 1 = 8 columns 20 / 4 = 5 spaces 5 + 1 = 6 rows 6 x 8 = 48 chairs, one mat 600 sq ft / 48 = 12.5 sq ft each Example count grid only. Chairs are not placed to any spacing or cover rule.
One dot per chair, using the calculator’s count rule for a 4 foot grid.

What Halving the Spacing Does to the Count

Halving 4 foot spacing to 2 feet on the same slab gives 11 x 16 = 176 chairs. That is 3.7 times the 48, so the calculator’s note that halving spacing roughly quadruples the chairs is loose. Use the exact count when you plan an order.

Chair count at 4 ft and 2 ft spacing Two bars for the same 20 by 30 foot slab with one mat, drawn to the same scale. The 4 foot spacing bar is 48 chairs. The 2 foot spacing bar is 176 chairs. The note says 176 divided by 48 is 3.7, so the count is 3.7 times as many, not four times. Chairs on one 20 by 30 foot slab 4 ft spacing 48 chairs 2 ft spacing 176 chairs 176 / 48 = 3.7 times as many, not four times
The 2 foot count is 3.7 times the 4 foot count, drawn to scale.

Mats multiply the count. Top and bottom mats double the grid, so the 48 chair grid gives 96 supports with two mats.

Where to Check Your Support Rules

Support rules come from your project specifications, your engineer and the manual your inspector uses. The sources here are consultant blogs, so they cannot replace those checks. Ask before you order supports.

Cover depends on the chair you pick, and the cover values belong to the rebar concrete cover guide. This article does not repeat them.

Count supports for your own slab

Enter your slab size and spacing in the chair count tool, then confirm the layout with your engineer.

FAQs About Rebar Supports

Are concrete dobies the same as rebar chairs?

No. A rebar chair is a plastic or metal support, while a concrete dobie is a precast concrete block. A consultant blog lists both as typical bar supports.

Can you use clay brick to support rebar?

No. A consultant blog says ACI 318, ACI 301 and CRSI prohibit clay brick as a bar support. Those code texts were not read, so this is a secondary claim. Follow your project specs.

Are concrete blocks allowed under rebar?

A consultant blog lists concrete blocks and concrete bricks as typical bar supports, so they are not ruled out there. It gives no sizes or strengths. Check product data and your engineer first.

How far apart should rebar chairs be?

The calculator guide says 3 to 4 feet is common. That is a general note, not a code limit, so confirm the spacing with your engineer or project specs before you order.

Does halving the chair spacing double the chairs?

No. On a 20 by 30 foot slab, 4 foot spacing gives 48 chairs and 2 foot spacing gives 176. That is 3.7 times as many, not double and not four times.

Do two mats double the chair count?

Yes. The calculator multiplies the grid by the number of mats. A 48 chair grid with top and bottom mats gives 96 supports, by the tool’s formula.

Who decides which rebar support to use?

Your project specifications and engineer decide. The sources in this article are consultant blogs, not a code text or a CRSI manual, so they cannot settle the choice. Ask your inspector.

Sources and Further Reading

References Used in This Article

The support guidance here comes from consultant blogs, because the code and CRSI texts could not be read. Check the manual your inspector uses. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-11.