Why does a wall plastered last month already show a hairline crack? Two engineering papers point to a short list of causes, and shrinkage during curing sits at the top.
Wall plaster cracks when stresses inside the coat exceed its tensile strength. For cement plaster, the largest movement is shrinkage during curing. Restraint from the lath and substrate, poorly proportioned mixes, premature water loss from heat and wind, and control joints all shape where cracks form.
Shrinkage During Curing Drives Most Movement
The largest movement in cement plaster is initial shrinkage during curing. Bowlsby of Simpson Gumpertz and Heger puts the wider point plainly: “Cement plaster cracking is inherently related to shrinkage and other movements.”
The coat wants to shrink as it cures. Whatever holds it back decides where the stress lands. The next sections cover those restraints, the mix, the weather and the joints.
How Lath and the Substrate Restrain the Coat
The lath and the wall behind it both limit how far the plaster can move. Bowlsby reports that lath fasteners and lath type both restrict cement plaster movement. The same paper says substrate movements can cause cracks, so the wall behind the coat matters too.
Cope and Horst, in a second engineering paper, add that corroded metal lath can result in excessive cracking. This is a secondary claim from one paper, and it is not backed by a standards document.
If the wall is built from masonry units, the units and their joints set the substrate you plaster against. Our guide to concrete block sizes covers the units themselves.
Mix Proportions Affect Coat Strength
Cope and Horst say stucco made from poorly proportioned mixes is often weak. Their stress rule is that cracks form when stresses exceed tensile strength, so a weaker coat has less margin before it cracks. The sources we read do not name one correct ratio, so use your plaster maker’s mix guidance.
The cement plaster calculator turns a mix ratio into cement and sand quantities, so you can check the numbers before you buy. Here is its worked example, hand-checked for this article:
- Plaster volume. 10 m2 x 0.012 m = 0.120 m3 of coat before bulking.
- Dry volume. 0.120 x 1.27 dry factor x 1.15 for 15 percent waste = 0.175 m3.
- Cement. 0.175 / (1 + 6) = 0.0250 m3. At an assumed 1,440 kg per cubic meter, that is 36 kg, or 0.72 of a 50 kg bag.
- Sand. 0.175 x 6 / 7 = 0.150 m3.
The calculator’s result panel shows 36 kg of cement and 0.150 m3 of sand, which match the hand check. The 1.27 factor and 15 percent waste are the page’s defaults.
Curing, Water Loss and Weather Set the Pace
Cope and Horst name premature loss of water from the stucco as a cause of distress. They tie that loss to high temperatures and to exposure to wind and sun. Both papers name curing, but neither gives a curing length we could verify.
Secondhand trade figures give curing periods, and they disagree with each other. We did not verify them, so this article gives no number. Follow your plaster maker’s data sheet for curing time.
What Control Joints Can and Cannot Do
Control joints are planned breaks in the coat. Bowlsby is cautious here: control joints have not been proven to solve all cement plaster cracking conditions.
Cope and Horst look at installation. In their investigations, poorly installed control joints were perhaps the most frequent cause of isolated cracking. Read together, the two papers say joints are not a cure-all and that installation still matters. We did not verify joint spacing, so ask your plaster maker or contractor for spacing rules.
Where Cracks Start and How to Check a Wall
The sources do not give a crack-pattern rule, so treat the flow below as a checklist for a closer look. Start with where the crack runs, then compare it with the causes above.
Write down the crack’s location, its direction and when you first saw it. Notes like these help whoever checks the wall.
Enter your area, thickness and mix in the plaster quantity tool to get cement and sand for your wall.
FAQs About Plaster Cracks
Why does plaster crack?
The coat cracks when stress builds up beyond its tensile strength. For cement plaster, the largest movement is initial shrinkage during curing.
Does curing time stop plaster from cracking?
Curing matters, because premature water loss from heat and wind is a named cause of distress. Neither source gave a curing duration we could verify, so follow your plaster maker’s data sheet.
Do control joints prevent all plaster cracks?
No. Bowlsby reports that control joints have not been proven to solve all cement plaster cracking. Cope and Horst also describe poorly installed joints as perhaps the most frequent cause of isolated cracking.
Does the mix ratio change plaster cracking?
It can. Cope and Horst say stucco made from poorly proportioned mixes is often weak, and a weaker coat has less tensile strength to resist stress. Neither source names a correct ratio.
Can corroded metal lath cause plaster cracks?
Yes, according to Cope and Horst, who state that corroded metal lath can result in excessive cracking. Bowlsby adds that lath fasteners and lath type both restrict plaster movement.
Is a crack along a joint a plaster problem?
It can be. Cope and Horst link poorly installed control joints to isolated cracking. Note where the crack runs and when you saw it, then compare the pattern with the causes in this article.
Does the Cement Plaster Calculator diagnose cracks?
No. The calculator estimates cement and sand for an area, thickness and mix. It does not find causes, so use the causes in this article to think through your wall’s crack pattern.
Sources and Further Reading
References Used in This Article
- Bowlsby, J., “Cement Plaster Metrics: Quantifying Stucco Shrinkage and Other Movements,” Simpson Gumpertz and Heger, Symposium on Building Envelope Technology, November 2010, accessed 2026-11-11.
- Cope, L. and Horst, M., “Common Sources of Distress in Stucco Facades,” Wiss, Janney, Elstner and Associates, RCI convention, March 2014, accessed 2026-11-11.
The causes here come from two engineering papers. Curing time and control-joint spacing were not verified, so follow your plaster maker’s data sheet. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-11.

Shakeel Muzaffar is the Founder and Editor-in-Chief, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality and formula verification to ensure accurate, practical, and easy-to-use calculators.